Operation Instruction
Miniature lathe
Please read this instruction carefully and keep it properly.
Preface
Dear users:
Thank you for using a mini lathe. This specification is only applicable to micro lathe products, all the contents in the book are only for user use and maintenance reference, not mentioned matters, welcome to consult the company’s customer service department.
For any machine problems, please contact us and We, we will
do our best to help you solve it.
If you have any suggestions or comments on this product,
please contact us and we will Actively improve the equipment.
May this product can bring you DIY fun, and also wish you
peace and joy.
Your satisfaction, our pursuit!
Notes for Safe Use
Warning: Do not touch the In operation saw blade and grinding wheel with your hands to avoid injury.
- Do not immerse the machine in
- Private modification is strictly prohibited, causing unnecessary
damage.
- Working time: please operate in strict accordance with the rated working time, each use shall not exceed two hours, continuous work for more than half an hour, must be shut down for 15 minutes, wait for the motor cooling before working.
- Do not allow processing of material exceeding SOMM and
- This product can not be directly connected to domestic electricity, it must be converted by power converter to motor and can use DC12v-24v electricity.
- Children must use the product with adults responsible for their safety, with supervision or guidance related to the use of the Take good care of the children to ensure that they do not play with the product privately.
- When using this machine, wear gloves to avoid
- If the product is not used for a long time, please place it in a dry place to avoid rust.
Product parameters
| motor speed | 4000-9000 RPM | Motor power | 96W |
| Machine size | 300*60*70mm | Drill model | B10 |
| Maximum blade diameter | 50mm | ||
| switch | Shift 2 switch | ||
| Drill chuck clamping range | 0.6-6mm | ||
| The lathe is 300mm long, can be 120mm long, 50mm diameter wood. | |||
| The motor cover and the saw blade shield are made of two materials, one iron shell material (gray or black) and one acrylic material (transparent). | |||
|
Enclosed metal chassis Double bearing tailstock Cutting tables Turning tool holder |
|||
Operating instructions
When you first use the product, make sure the machine is connected to the power cord and running normally. All accessories that need to be used must be installed in case of power failure.
All features need to be used with the accessories. If the purchase package does not contain this attachment, you cannot use this feature. These accessories can be configured by yourself, or contact the merchant to purchase.
- Wood car cutting use
Thimble card the center of the wood, adjust the position of the tail seat according to the length of the wood, shake the wood
.’ with your hand, have no shaking feeling, and
” then start the operation. Put the carving knife under the center of the wood, enter the knife slowly, and move evenly at the left and right sides. (Sharp knife, car hardwood)
- Saw mounted for use
Combine the blade joint rod and the blade installation together. The screw in front of the blade should be tightened to avoid flying, and then put the blade into the knife holder to cut.It is
recommended that after the whole wood
car is finished, use the saw blade for sequential separation.
3 .Installation and use of the grinding plate Stick the grinding sandpaper to the
grinding plate, and then install the grinding plate on the drill clip head, holding the required grinding objects can work.Remove the separated beads and polish them
- The punch parts are used
After grinding, you need to use the perforated tail seat for drilling, so as to facilitate the subsequent production.
- The retainer is used
Hand-held circle repair device, different sizes of Buddha beads choose different sizes of circle repair circle. The round machine is only to on the edges of the knife marks, and it is not recommended to exert excessive force)
- Sand paper grinding
Finally, use sandpaper (from coarse to fine) for fine grinding.
failure recovery
- The machine does not turn
- After the power supply is plugged in the house, if the power indicator is not on or flashing, the power supply is broken,
- lf the machine is not energized, turn the clamlet by hand. If the resistance is not smooth, the motor slips and the motor needs to be
- If the power supply indicator light is normal and the motor is not abnormal, the switch line can be disconnect and the direct socket is connected to the motor. If the line turns normally, the switch is short circuit and the switch should be replaced.
- The above is no problem, you can contact the manufacturer for testing and replacement.
- Machine concentric degree
Machine concentricity is the same center point between the drill pin head and the thimble of the tail pin, rather than comparing the height of the drill clamp head and the tail seat. When all the machines leave the factory, the concentricity has been adjusted. If there is a different heart of the machine, please contact us.
Reviews
There are no reviews yet.