![\"\"](\"https:\/\/roboticaplus.com\/wp-content\/uploads\/2024\/06\/Banner-Arduino-Pin-Configurations-Robu-300x150.webp\")
<\/p>\n<\/p>\n
Details<\/p>\n
Material: plastic
\nColor: white, transparent
\nAssembly Required: Yes
\nDisplay type: no display
\nPower mode: USB
\nOperating voltage: \u226436V
\nLaser products: without laser
\nBattery characteristics: without battery
\nItem ID: QC43289
\nThis is a Super Starter Leaning Kit for Arduino MEGA 2560, this kit contains more than 37 kinds of different electronic components, more than 20 components included.
\nWith this kit, we will take you from knowing to exploitation, you can do more experiments, bring your idea to real operation without the limitation of hardware and software, and we have carefully prepared a guide book
\n(120 pages PDF manual) and supporting experimental code routines for you, including a total of 33 experiments.
\nWe believe that with this hardware + software support, you can become an expert programmer (developer) very soon. So don’t waste time, just get this kit and start your project right away!
\nWe will send you all the files (schematic, code, tutorial, specification, etc.) to your email address when you receive the board. Please contact us by email if you need it urgently. We also provide technical support. We are happy to solve the problem that you encounter while using this kit.<\/p>\n
![\"Super](\"https:\/\/img.kwcdn.com\/product\/Fancyalgo\/VirtualModelMatting\/69b447d0a5b019ab109c2007999a412b.jpg?imageView2\/2\/w\/800\/q\/70\/format\/webp\")
![\"Super](\"https:\/\/img.kwcdn.com\/product\/Fancyalgo\/VirtualModelMatting\/6ee6f2c0e78fe2904b60f74bd6b22a8c.jpg?imageView2\/2\/w\/800\/q\/70\/format\/webp\")
<\/p>\n
We provide the following classes for now.<\/p>\n
Regarding Arduino
\nLesson 0 IDE installation
\nLesson 1 Add libraries and open a serial monitor
\nLesson 2 Blink
\nLesson 3 LED
\nLesson 4 RGB LED
\nLesson 5 Digital inputs
\nLesson 6 active buzzer
\nLesson 7 Passive buzzer
\nLesson 8 Tilt Ball Switch
\nLesson 9 Servo
\nLesson 10 Ultrasonic sensor module
\nLesson 11 DHT11 temperature and humidity sensor
\nLesson 12 Analog joystick module
\nLesson 13 IR receiver module
\nLesson 14 LCD display
\nLesson 15 thermometer
\nLesson 16 Eight LED with 74HC595
\nLesson 17 The serial monitor
\nLesson 18 photo booth
\nLesson 19 74HC595 and segment display
\nLesson 20 Seven segment digital display
\nLesson 21 DC motors
\nLesson 22 relay
\nLesson 23 stepper motor
\nLesson 24 Controlling a stepper motor with a remote control<\/p>\n
List of components:
\n1 pcs UNO R3 controller board; 1 pcs LCD1602 module (with pin header); 1 pcs breadboard expansion board; 1pcs power supply module Warning: Please. Do not use a voltage higher than 9V
\n1 pcs joystick module; 1 pcs IR receiver; 1 pcs servo motor (SG90); 1 pcs stepper motor; 1 pcs ULN2003 stepper motor driver board
\n1 pcs ultrasonic sensor; 1 pcs DHT11 temperature and humidity module; 1 pcs 9V battery with DC; 1 units jumper wire 65
\n1 pcs USB cable; 1 active buzzer units; 1 pcs passive buzzer; 1 units potentiometer; 1 pcs 5V relay
\n1 bread board units; 1 remote control units; 1 pcs tilt switch; Button 5 pcs (small); 1 display units 1 digit with 7 segments; 1 display unit with 4 digits and 7 segments
\n5 pcs yellow LED; 5 pcs blue LED; 5 pcs green LED; 5 pcs red LED; 1 pcs RGB LED
\n2 units Photoresistor; 1 thermistor units; diode rectifier 2 units (1N4007); 2 units NPN transistor (PN2222)
\n1 pcs IC 74HC595; 120 resistor units; 10 units of dupont thread female to male<\/p>\n
![\"Super](\"https:\/\/img.kwcdn.com\/product\/fancy\/a6ed6ffe-0f2c-4f8b-b9a4-412965c12108.jpg?imageView2\/2\/w\/800\/q\/70\/format\/webp\")
<\/p>\n","protected":false},"excerpt":{"rendered":"
![\"\"](\"https:\/\/roboticaplus.com\/wp-content\/uploads\/2024\/06\/images.jpeg\")
<\/p>\n